A usable fastener quotation needs the product type, standard or drawing, nominal diameter, length, property grade, material, surface finish, order quantity and delivery destination. For structural bolts, please also confirm whether the project requires ASTM A325 or A490, and whether hot dip galvanizing is specified. For custom items, send the drawing or a dimensioned sketch so the thread length, bend radius and projection can be confirmed before pricing.

Yes. Common references include ASTM A325 / A490 structural bolts, ASTM A193 B7 / B7M / B16 stud bolts, DIN 931 / 933 hex bolts, DIN 975 / 976 threaded rods, DIN 125 / 127 washers, GB/T 1228 structural bolts and ISO 4014 / 4017 hex bolts. If the project specification references a standard not listed here, send the clause or drawing and the requirement can be reviewed before quotation.

Yes. Non-standard dimensions, thread lengths, bend configurations, material grades and surface finishes can be produced against a drawing. Typical custom items include L / J / U foundation bolts, special stud bolts for pressure equipment, and anchor rods with specified thread engagement. For evaluation, send the drawing with diameter, total length, thread length, material grade, surface treatment and order quantity.

MOQ depends on product type, size, material and whether tooling is required. Standard stock items usually start from one pallet or one ton. Custom bent foundation bolts, special studs and non-standard washers are reviewed case by case because of setup and material minimums. If the requirement is below the normal MOQ, it is still worth sending the spec — in some cases small trial quantities can be arranged alongside a larger production run.

Standard fasteners are usually delivered 15 to 30 days after order confirmation, depending on size, coating and quantity. Hot dip galvanized items and custom bent anchor bolts typically need longer because of coating and forming steps. Third-party inspection, if required, adds time before shipment. For project schedules, send the required on-site date so production and inspection can be planned backwards from it rather than quoted as a flat lead time.

Common finishes include zinc plated, hot dip galvanized, black oxide, Dacromet and customer-specified coatings. Zinc plating is typical for indoor or sheltered applications; hot dip galvanizing is used for outdoor structural and foundation work where coating thickness and salt spray resistance matter. Dacromet is often selected where zinc plating is not sufficient but hot dip galvanizing is not practical. Finish should be confirmed against the project’s corrosion class and expected service life.

Material traceability documentation and third-party inspection reports can be provided when required by the project specification. Typical documents include heat number and steel grade records, mechanical property reports, coating thickness measurements and salt spray test data. Inspection by SGS, BV or a customer-nominated agency can be arranged before shipment. Please state the document requirement in the inquiry so it is included in the quotation rather than added later.

FOB, CIF, CFR and DDP can be discussed according to destination port and project delivery requirements. FOB is common for customers with their own forwarder; CIF and CFR are used when shipping cost should be included in the quotation. DDP can be reviewed for project deliveries where customs clearance and inland transport need to be handled by the supplier. The trade term affects both pricing and responsibility split, so it should be confirmed at inquiry stage.

Samples can be arranged for evaluation. Sample cost and freight are confirmed based on product type and destination. For standard items, samples are usually drawn from current stock. For custom or coated items, a small trial batch may be produced, which affects both cost and lead time. When requesting samples, confirm the specification to be tested, the quantity needed and whether the sample should match the production finish exactly.

Typical applications include steel structures, bridges, infrastructure, industrial plants, pressure equipment, machinery, energy projects and engineering procurement. Structural bolts and foundation bolts are used in steel frame and equipment base work; stud bolts are used in flange and piping connections; anchors and threaded rods are used in concrete fixing and support systems. The same product category can require different standards depending on the industry, so the application should be stated in the inquiry.

Send the product name, standard or drawing, diameter, length, grade, material, surface finish, quantity and delivery destination through WhatsApp, email or the inquiry form. Drawings can be attached for project-specific requirements. If the standard is not yet decided, describe the application and load condition instead — the requirement can be reviewed and a suitable reference proposed before pricing.